Bathroom Addition - V2 | Page 6 | Construction and DIY projects | Forums

A A A
Avatar

Please consider registering
Guest

Search

— Forum Scope —






— Match —





— Forum Options —





Minimum search word length is 3 characters - maximum search word length is 84 characters

Register Lost password?
sp_Feed F-Construction-and-DIY
Bathroom Addition - V2
Avatar
icanreachit
Farm Hand
Members
Forum Posts: 562
Member Since:
27 Aug ’14
sp_UserOfflineSmall Offline
41
30 Sep ’15 - 10:04 am
sp_Permalink sp_Print

That's my plan. Or just put some quarter round or other trim at the base of the wall.

Ran into two issues last night as I started to excavate for the beams:

There's a concrete beam beneath the brick wall - Will likely have to cut this, or pour around it. Waiting to hear back from the civil engineer but I'm assuming that it would be best to remove it.

There's a gas line running plumb through the middle of where I need to run the slab - I'm having the plumber who will do the rough in plumbing come move the gas line so that it skirts the perimeter + 2'

I believe that I could do the rough plumbing myself but don't want to risk it with the concrete being permanent and all.

Avatar
K
Admin
Forum Posts: 31782
Member Since:
15 Feb ’12
sp_UserOfflineSmall Offline
42
1 Oct ’15 - 10:10 am
sp_Permalink sp_Print

If it's not in the way I would just pin it and pour around it. I use to do my rough in plumbing but my wife always complained the drains were too slow, I told her to stop running so much water, I barely ducked the cup thrown at me. 

Avatar
icanreachit
Farm Hand
Members
Forum Posts: 562
Member Since:
27 Aug ’14
sp_UserOfflineSmall Offline
43
1 Oct ’15 - 1:22 pm
sp_Permalink sp_Print

With the house being built in '55 and a lot of arguments against it I'd rather play it safe. As far as the plumbing goes: did you ever figure out why your drainage was slow? I've always thought that to be inadequate venting.

Avatar
K
Admin
Forum Posts: 31782
Member Since:
15 Feb ’12
sp_UserOfflineSmall Offline
44
1 Oct ’15 - 1:25 pm
sp_Permalink sp_Print

Pretty much what the issue was, I learned a lot when we paid someone to rough in our house.

Avatar
icanreachit
Farm Hand
Members
Forum Posts: 562
Member Since:
27 Aug ’14
sp_UserOfflineSmall Offline
45
2 Oct ’15 - 2:17 pm
sp_Permalink sp_Print

Yeah, I heard back from my plumber so I'll have him do the rough in. I'm torn on the slab: I'd love to do it myself ($$$) but my wife wants to have it hired out. Best price right now is $3750 but I know better than to take the best price. The next price is around $4500. Still seems absurdly high.

Avatar
K
Admin
Forum Posts: 31782
Member Since:
15 Feb ’12
sp_UserOfflineSmall Offline
46
3 Oct ’15 - 9:45 am
sp_Permalink sp_Print

weekend spa trip for the wife? Yell surprise when she get's home and show her the new slab?

Avatar
icanreachit
Farm Hand
Members
Forum Posts: 562
Member Since:
27 Aug ’14
sp_UserOfflineSmall Offline
47
4 Oct ’15 - 8:47 pm
sp_Permalink sp_Print

Still no luck with the concrete guys and of course, I'm inherently getting better quality by doing it myself. However, I may have made a mistake.

Because the slab is partially raised, I cut 8" of soil off of the top, dug the trenches, and then started to place the crushed rock and tamp it. Only problem? The sides of my internal rectangle are collapsing into the trenches.

How is this usually done? Cut off the top 8, place and tamp, then cut trenches? This is what I will do for the second section.

Now that I'm where I am, I don't know a good way to fix it. I know for taller monolithic slabs you can build up the interior with woven sand bags. With that said, can I get away with bags of concrete? The woven sand bags are on Amazon but then I would have to go through the labor of filling them so for $3 I can just get pre-filled bags of concrete.

All thoughts appreciated! Hoping that I didn't shoot myself in the foot.

Avatar
K
Admin
Forum Posts: 31782
Member Since:
15 Feb ’12
sp_UserOfflineSmall Offline
48
4 Oct ’15 - 9:04 pm
sp_Permalink sp_Print

cut the sides back at a 45 degree angle and tamp it, so it looks like this, will keep from caving in and make the slab stronger at those points

Forum Timezone: America/New_York

Most Users Ever Online: 698

Currently Online:
13 Guest(s)

Currently Browsing this Page:
1 Guest(s)

Top Posters:

easytapper: 2149

DangerDuke: 2030

groinkick: 1667

PorkChopsMmm: 1515

Gravel Road: 1455

Newest Members:

deweyvoyles1

lonniekqh5

isabellrubio59

joette850

rosemariehouldin

Forum Stats:

Groups: 1

Forums: 12

Topics: 11479

Posts: 58674

 

Member Stats:

Guest Posters: 2

Members: 3589

Moderators: 0

Admins: 1

Administrators: K